การแนะนำ
The New K-Type Axial Feeder is built as a complete component-preparation engine rather than a simple tape advancer. Into its guides goes the everyday inventory of through-hole assembly — resistors, diodes, fuses, inductors, and axial capacitors — spanning a deliberate spread of body sizes and lead diameters, all consolidated within a single specification range. What leaves the feeder is quite different from what entered: a formed, gauged, insertion-ready part.
Between entry and exit runs an unbroken kinematic chain. The taped strip advances on a metered pitch; the tape is stripped away; the leads are cut to length, then bent and formed against fixed tooling datums; and the finished component is presented at the pickup point in a controlled, repeatable pose. No stage releases the part into free handling — every transfer is a positive mechanical hand-off, so the geometry created at the cutting and forming stations survives intact to the moment of insertion.
Holding this chain together is the feeder’s pitch discipline. Because each index is metered rather than estimated, the forming tools meet every component at the same coordinates, and the finished lead span registers precisely to the hole spacing of the board it will enter. Output cadence locks to the insertion machine’s cycle, so the K-Type delivers not merely components but a metronomic stream of identical, correctly formed parts — geometry and timing arriving as one.
เครื่องป้อนแบบแกนแนวตั้งรุ่น K ใหม่
The Full Axial Feed: Feeding Resistors, Diodes, Fuses, and Inductors with the New K-Type
A smart robot electronics factory rarely builds just one product. Power distribution boards, battery management modules, sensor interface cards, and actuator controllers all pass through the same insertion line, each with its own component mix. The New K-Type Axial Feeder is engineered for exactly this diversity, handling the full spectrum of axial-leaded parts that robot electronics depend on.
Its feeding range covers carbon and metal-film resistors, general-purpose and fast-recovery diodes, axial fuses, ferrite inductors, and wire jumpers — the workhorse components that give robot boards their power handling, circuit protection, and signal conditioning. Lead diameters and body lengths vary widely across these parts, yet the K-Type’s adjustable forming and transport geometry accepts them without extensive retooling.
Changeover is where the feeder proves its value on a mixed-model line. Tape reels swap quickly, pitch settings adjust in seconds, and the compact footprint allows multiple K-Type units to sit side by side, each dedicated to a different component in the sequence. For a factory building control boards for mobile robots in the morning and charging infrastructure after lunch, the New K-Type turns component variety from a scheduling headache into a routine, well-ordered step in the process.
ข้อกำหนด
| แบบอย่าง | YN-A2412 |
| Dimensions (ความยาว * ความกว้าง * ความสูง หน่วย: มม.) |
536×109×140.5 มม. |
| น้ำหนัก | 9 กิโลกรัม |
| Operating Voltage | DC 24V |
| ปริมาณอากาศที่จำเป็น | 0.5–0.7 Mpa |
| กระแสไฟฟ้าสูงสุด | 1.3A |
| ความเร็วในการให้อาหาร | 2 ชิ้น/ชุด |
| โหมดการขับขี่ | ระบบอากาศอัด |
| แผงควบคุมการทำงาน | หน้าจอสี TFT ขนาด 0.96 นิ้ว, 80 × 160 พิกเซล |
| ข้อผิดพลาดในการกำหนดระยะห่างระหว่างวัสดุ | ±0.4 มม. |
| ความกว้างของเทปที่ใช้ได้ | 63–90 มม. |
https://www.youtube.com/@allaismt
For more information about the เครื่องป้อนแบบแกนแนวตั้งรุ่น K ใหม่, โปรดส่งอีเมลไปที่
เราจะตอบข้อสอบถามของคุณอย่างรวดเร็วและให้ข้อมูลโดยละเอียดเกี่ยวกับผลิตภัณฑ์และบริการของเรา.
