Introdução
A radial feeder with an integrated cutter transforms vertically taped electronic components through a sequenced process of automated feeding, lead forming, cutting, and bending. Radial components arrive in tape format, indexed forward at controlled intervals. The built-in cutter severs each lead wire to the required length while a forming mechanism shapes and bends the leads to match the target PCB footprint. The unit then presents each prepared component at a fixed pickup position, ready for the downstream insertion head to retrieve and place.
Mounting the radial feeder onto an SMT placement machine or a dedicated labeling platform enables direct DIP component placement within a surface-mount workflow. This eliminates the manual hand-insertion step after reflow, reducing line transitions and labor dependency. The feeder synchronizes with the host machine’s pick-and-place cadence, delivering one component per cycle at the precise moment the insertion nozzle arrives.
For odd-form automation, the radial feeder integrates with dedicated insertion machines tailored to specific board layouts and component geometries. Custom configurations allow the feeder to match varying machine interfaces, select whether the carrier tape is severed post-feed, and determine if lead bending is required. When paired with non-standard automation cells, the feeder supports combined operations — automatic insertion, heat-shrink tubing application, and inline component forming — all within a single continuous sequence.
Radial Feeder With Cutter(48mm Width)
Radial Feeder With Cutter Consumer Electronics DIP Component Automated Insertion
In a consumer electronics assembly line, the radial feeder mounts directly onto the SMT placement machine, feeding vertically taped radial components — electrolytic capacitors, LEDs, inductors — into the same pick-and-place workflow used for chip components. The feeder indexes the tape forward, trims each lead to the programmed length, and bends the leads to match the PCB footprint. A formed component is then presented at the pickup position, where the placement nozzle retrieves it and places it onto the board without interrupting the surface-mount cycle.
This integration eliminates the traditional split between SMT and through-hole processes. Boards no longer travel to a separate hand-insertion station after reflow. Instead, DIP radial parts are placed inline, alongside resistors and ICs, within a single pass. The result is a shorter overall line, fewer changeover steps, and a reduced headcount at the insertion stage — all critical in high-volume consumer electronics production where line balance and throughput per square meter determine unit cost.
For boards that mix surface-mount and through-hole radial components, the feeder also connects to dedicated odd-form insertion machines. Here the feeder is configured to match the specific machine interface, with options for tape cutoff after feeding and lead bending on or off. In smartphone mainboard and tablet PCB lines, this setup handles bulk capacitors and power inductors that cannot be converted to SMD packages, delivering formed components at the insertion head’s cycle rate without manual pre-forming or hand-loading.
Especificações
| Modelo | YN-R2203 | YN-R2201 | Observações |
| Dimensões (C × L × A) | 740 × 47 × 144 (110) mm | 750 × 68 × 144 (110) mm | Altura da captação inferior: 110 mm Altura máxima (da base até a alça): 144 mm |
| Peso | 6 kg | 8 kg | |
| Operating Voltage | DC 24V | DC 24V | |
| Abastecimento de ar necessário | None | None | |
| Corrente máxima | 3A | 3A | |
| Feed Speed | 0,6–2 s/unidade | 0,6–2 s/unidade | |
| Método de acionamento | Totalmente elétrico | Totalmente elétrico | |
| Painel de operação | TFT colorido de 0,96″ Resolução da tela: 80×160 pixels |
TFT colorido de 0,96″ Resolução da tela: 80×160 pixels |
|
| Erro no passo de corte do material | ±0,2 mm | ±0,2 mm | |
| Espaçamento aplicável entre as fitas | 12,7 mm/15 mm | 12,7 mm/15 mm | Peças de reposição necessárias |
| Função de corte de fita | Opcional | Opcional | YN-R2203: Com cortador YN-R2201: Sem cortador |
| Função de flexão | Opcional | Opcional | A dobra pode ser personalizada de acordo com o tipo de material |
| Vida útil da lâmina | ≥1 milhão de vezes | ≥1 milhão de vezes |
https://www.youtube.com/@allaismt
For more information about the Radial Feeder With Cutter (48mm Width), Por favor, envie um e-mail para
Responderemos à sua solicitação prontamente e forneceremos informações detalhadas sobre nossos produtos e serviços.
