소개
Yinuo Automatic Long Front Pushing Feeder is designed for automatic peeling and feeding of roll-format materials, covering paper labels, protective films, foam, double-sided tape, conductive adhesive, copper foil, steel plates, and reinforcement boards. Its industrial-grade construction and broad material compatibility allow it to serve reliably across a range of SMT, 3C electronics, and logistics production environments.
The feeder offers configurable feeding parameters and operates in either online mode or automatic mode depending on the application. A color touchscreen serves as the primary interface for displaying and adjusting operational parameters, keeping setup and monitoring accessible to line operators. Built-in abnormal alarm output and remote reset support help maintain line continuity without requiring frequent manual checks. For equipment integration, the feeder supports selectable GPIO or RS232 communication, accommodating different control system requirements.
After integration into automated equipment, the feeder enables stable and repeatable material supply with minimal interruption to production flow. It excels in environments where roll-material feeding precision and feeding speed are critical to line performance — particularly in SMT manufacturing, 3C electronics assembly, and logistics-related automation. The combination of dual operating modes, configurable parameters, and standard communication options provides a practical and adaptable feeding solution for automated production setups.
Yinuo Automatic Long Front Pushing Feeder
Applying Yinuo Automatic Long Front Pushing Feeder in Battery Charger Assembly
On a battery charger assembly line, the feeder sits at a station where labels or surface films need to be supplied to either an automated pick-and-place head or a manual placement position. Yinuo Automatic Long Front Pushing Feeder takes the loaded material reel, peels the liner automatically as the material advances, and presents each label at a consistent pick location. The feeding cycle is triggered by the host machine in online mode or runs on its own internal timing in automatic mode, depending on how the station is configured within the overall line layout.
When the product batch changes to a different charger variant, the operator interacts with the color touchscreen to modify feeding parameters — pitch, speed, and delay timing — to match the new label specifications. These adjustments are entered directly on the interface without opening the machine or swapping mechanical components. The feeder stores the settings for each charger model, so operators can recall them when the production schedule returns to a previously configured variant. The transition between configurations happens within the batch changeover window, keeping downtime brief.
Throughout the production shift, the feeder cycles continuously: peel, advance, hold, release — then repeat. If a feeding fault occurs, the alarm output notifies the line controller, which can pause the upstream and downstream equipment as needed. The operator reviews the fault through the touchscreen, addresses the material issue, and sends a remote reset command via GPIO or RS232 from the line control panel. The feeder clears the fault state and resumes the feed cycle without requiring a manual restart at the machine itself. This working sequence — configure per model, run automated feed cycles, handle faults remotely — integrates the feeder into the charger production workflow as a responsive and low-maintenance material supply unit.
명세서
| 목 | 사양 | Parameter | 사양 |
| 수유 방법 | Peel tape onto receiving platform, then pick up | Operation Interface | 3.5″ TFT color screen, 480×320 resolution, capacitive touchscreen |
| Material Type | Tape-on-reel | 급식 속도 | Stepless speed regulation, max 100mm/s |
| 전압 | DC 24.0V | 대기 전력 | <20W |
| 현재 | 최대 5.0A | Operating Temperature | -20°C to 65°C |
| 급이정확도 | ±0.2mm | 작동 습도 | 20% to 90% RH, no condensation |
| Material Position Adjustment | X-direction: mechanical limit adjustment; Y-direction: software adjustment; Z-direction: mechanical adjustment |
보관 온도 | -40°C to 85°C |
| Input Air Pressure | 0.40MPa to 0.60MPa | 보관 시 습도 | 10% to 95% |
| 통신 인터페이스 | GPIO NPN/PNP 유형 | Lifespan | 20,000시간 이상 (25°C) |
| Program Interface | GPIO 232, TCP/IP | 치수 | Refer to actual product specifications |
| 구동 방식 | Motor + pneumatic | 무게 | Refer to actual product specifications |
https://www.youtube.com/@allaismt
For more information about the Yinuo Automatic Long Front Pushing Feeder, 자세한 내용은 이메일을 보내주세요.
문의하신 내용에 신속하게 답변드리고 당사 제품 및 서비스에 대한 자세한 정보를 제공해 드리겠습니다.
