High Temperature Tape Cutting Feeder Lithium Battery Assembly Automation

Introduzione

The feed sequence inside this Yinuo Cutting Feeder runs on a push-and-hold relay between two clamp assemblies. The front clamp releases while the rear clamp takes command — it grips the tape and advances the material tip into the front clamp zone, then the front clamp locks down and the rear clamp lets go, retreats to a predetermined setback, and re-grips the strip. This handoff keeps the tape under constant control, never floating free between feed cycles. For thin high-temperature films that buckle at the slightest slack, that constant tension is the difference between a straight feed and a skewed strip that the nozzle cannot pick reliably.

Once the front clamp secures the tape, the nozzle descends and makes contact with the segment suspended above the cutting anvil. Vacuum lock is confirmed, the cutting mechanism strokes through the material, and the front clamp releases immediately after the blade clears the tape path. The nozzle lifts the freshly cut piece and transfers it to the placement target without pause. The entire cut-to-lift transition happens in a window measured in milliseconds, with the blade fully retracted before upward nozzle travel begins — a timing discipline that prevents edge drag, adhesive smear, and the microscopic tears that degrade cut quality over thousands of cycles.

What makes this Yinuo Cutting Feeder adaptable across a lithium battery line is the parameter set stored behind each motion. Feed length, clamp stroke, setback distance, and blade depth are configured through a touch panel and saved as named recipes. When the line switches from narrow tab insulation tape to full-cell wrap material, the operator recalls the corresponding recipe and the feeder reconfigures itself. The rear clamp advances further or shorter, the front clamp adjusts its grip force, and the blade strokes to the correct depth — all without mechanical retuning. In a production environment where multiple tape types rotate through the same station daily, this recipe recall recovers minutes per changeover that compound into hours of recovered time per week.

Yinuo Cutting Feeder

High Temperature Tape Yinuo Cutting Feeder Lithium Battery Assembly Automation

A single lithium battery line rarely runs one tape type — polyimide for cell insulation, PET for tab masking, glass-cloth barrier and double-sided adhesive for pack assembly. Each material grips, cuts, and releases differently. The Yinuo Cutting Feeder manages this variety through stored recipes that remember feed length, clamp force, blade depth, and setback distance per tape specification. The rear clamp advances the strip into the front clamp zone, the front clamp locks at the correct pressure, the nozzle picks up, the blade cuts, the clamp releases, and the nozzle lifts. Every parameter in that chain is recalled, not re-entered, when an operator switches materials.

The blade system reinforces this adaptability. A single feeder accepts multiple cartridge profiles — straight edge for clean polyimide cuts, micro-serrated for glass-cloth reinforcement, coated surfaces for silicone adhesives that foul untreated steel. Swapping a cartridge takes under a minute and requires no recalibration because the stored recipe already knows the blade depth and stroke parameters. For a contract manufacturer running short batches of three cell formats in a single shift, this means the cutting station pivots as fast as the line does. No dedicated feeder per tape type, no compromise blade that cuts everything poorly, no operator hunched over a dial indicator during changeover.

The competitive edge here is inventory consolidation and line flexibility. Battery factories expanding into multiple cell formats face a multiplying equipment footprint if each tape type requires its own dedicated cutting unit. Our feeder collapses that requirement. One unit, a drawer of cartridges, a library of recipes, and the line stays lean. For operations managers balancing CapEx against production agility, a feeder that serves multiple materials without multiplying machine count is not a convenience — it is a budget strategy that pays for itself in floor space saved and changeover minutes recovered.

Specifiche

https://www.youtube.com/@allaismt

For more information about the Yinuo Cutting Feeder, si prega di inviare una e-mail a

info@allaismt.com

Risponderemo tempestivamente alla tua richiesta e ti forniremo informazioni dettagliate sui nostri prodotti e servizi.