In operation, the feeder takes tinned copper wire directly from a reel and completes the entire preparation cycle automatically: the wire is straightened, metered to the programmed length, cut, and formed into a consistent U-shaped jumper ready for insertion. The operator simply loads the reel and sets the wire diameter, cut length, and insertion span through the control panel. Servo-driven feed rollers then deliver the wire at a steady, repeatable rate that matches the rhythm of the insertion head, allowing the line to run continuously without manual wire handling.<\/p>\n
This automatic preparation process is where the product’s value becomes visible. Every jumper leaves the feeder with identical leg length and bend geometry, which means stable insertion, uniform solder joints, and far fewer downstream defects. Compared with manual cutting and hand insertion, one feeder can sustain high-volume output around the clock, reduce labor on the line, and keep board quality consistent across entire production shifts.<\/p>\n
<\/p>\n
![\"Automatic](\"https:\/\/esmte.com\/wp-content\/uploads\/2026\/08\/Automatic-Jumper-Feeder.png\")
Automatic Jumper Feeder<\/p><\/div>\n
<\/p>\n
Automatic Jumper Feeder for Regulated Wire Tension Control in Battery Module Assembly<\/h2>\n
In battery power electronics factories, the Automatic Jumper Feeder<\/strong> serves as the primary supply device for preparing interconnect jumper wires that bridge cell terminals and module busbars. The device accepts reeled copper wire as input material, drawing the wire from the reel through a controlled feed path that maintains consistent tension throughout the unwinding process. This regulated material handling is essential in battery manufacturing, where interconnect jumpers must retain uniform conductivity and dimensional integrity to ensure stable power transfer between battery cells and across module assemblies.<\/p>\n The feeder’s reeled-wire processing capability operates as a continuous, integrated cycle. As wire is pulled from the reel, it is measured to the programmed feed length, cut cleanly at the designated point, and formed into the jumper geometry required by the battery module design. The device then presents each finished jumper to the insertion machine in the correct orientation for automated placement. This uninterrupted reel-to-insertion flow eliminates the staging, pre-cutting, and manual sorting operations that typically interrupt material supply in battery assembly lines, allowing interconnect preparation to keep pace with high-volume module production schedules.<\/p>\n The market value of this reeled-wire feeding capability is particularly pronounced in battery power electronics, where production volume is scaling rapidly to meet energy storage and electric mobility demand. Manufacturers deploying the Automatic Jumper Feeder gain a supply device that converts bulk reeled copper directly into insertion-ready interconnect jumpers without labor-intensive preprocessing. The result is lower material handling cost, reduced wire waste through precise cut-to-length control, and a continuous supply flow that sustains module assembly throughput\u2014capabilities that directly strengthen a battery manufacturer’s competitive position in a capacity-constrained market.<\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n![\"\"](\"https:\/\/esmte.com\/wp-content\/uploads\/2026\/08\/Jump-Wire-Roll-1-1.png\")
<\/p>\n<\/h2>\n
\u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0
![\"\"](\"https:\/\/esmte.com\/wp-content\/uploads\/2026\/07\/\u80cc\u666f\u677f_\u526f\u672c_\u526f\u672c.png\")
\u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0 \u00a0![\"\"](\"https:\/\/esmte.com\/wp-content\/uploads\/2026\/08\/MBXY-CR-b969efebf85f4b1dc3b4d8b926a13202_\u526f\u672c-scaled.png\")
<\/h2>\nSpecifik\u00e1ci\u00f3k<\/h2>\n
\n\n
\n Modell<\/strong><\/td>\n YN-J2303<\/strong><\/td>\n Remarks<\/strong><\/td>\n<\/tr>\n \n Dimensions (L\u00d7W\u00d7H)<\/strong><\/td>\n 624\u00d778\u00d7160mm<\/strong><\/td>\n <\/td>\n<\/tr>\n \n S\u00faly<\/td>\n 6.5KG<\/td>\n <\/td>\n<\/tr>\n \n Operating Voltage<\/td>\n DC 24V<\/td>\n <\/td>\n<\/tr>\n \n Air Supply Required<\/td>\n None<\/td>\n <\/td>\n<\/tr>\n \n Maximum Current<\/td>\n 2.5A<\/td>\n <\/td>\n<\/tr>\n \n Feed Speed<\/td>\n 1.5s\/Pcs<\/td>\n <\/td>\n<\/tr>\n \n Operation Panel<\/td>\n 0.96″ TFT
\nColor Screen Resolution: 80\u00d7160 pixels<\/td>\n<\/td>\n<\/tr>\n \n Changeover Time<\/td>\n 3min<\/td>\n <\/td>\n<\/tr>\n \n Channel<\/td>\n Single Channel<\/td>\n <\/td>\n<\/tr>\n \n Lead Bending Function<\/td>\n Bending<\/td>\n <\/td>\n<\/tr>\n \n Pre-lift Function<\/td>\n Pre-lift available<\/td>\n <\/td>\n<\/tr>\n \n Cut-off Function<\/td>\n Cut-off<\/td>\n <\/td>\n<\/tr>\n \n Correction Function<\/td>\n Correction<\/td>\n <\/td>\n<\/tr>\n \n Material Wire Diameter<\/td>\n 0.4\u20131mm<\/td>\n Cannot use 0.6mm forming die to form 0.4mm wire;
\nCan only use 0.6mm die for 0.6mm wire<\/td>\n<\/tr>\n\n Track Pitch<\/td>\n 5\u201326mm
\n(Forming die depends on wire diameter)
\nCross-shaped die: 3 sizes in one set (large\/medium\/small)<\/td>\nCannot use 16mm forming die for 16mm track pitch;
\nMust use 16mm length die<\/td>\n<\/tr>\n\n Forming Lead Length<\/td>\n 2.0~5.5mm<\/td>\n Within this range, different lengths can only be achieved
\nby using different forming dies of corresponding sizes<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n